50M HDMI Extender(Set)
50M HDMI Extender(Set) History Product Johor Bahru (JB), Malaysia, Masai, Skudai Supplier, Wholesaler, Supply, Supplies | Celtech Technology Sdn Bhd

50M HDMI Extender (Set)

Model: STR50C-HDV

  • Allows HDMI Audio/Video and IR signals to be transmitted over a single Cat5e/6 cable.
  • Support copy EDID from receiver display or loop out display
  • Allows for cascading via additional HDMI loop out port. Support Power over cable function.
  • Transmission Range: Extends 1080p resolution up to 164ft/50m over a single Cat5e or Cat6 cable
  • Works with HDMI and HDCP compliant devices
  • Supports up to 1080p High Definition resolution
  • Compact design for an easy and flexible installation.
Panel descriptions:
1.       Transmitting unit

HDMI in: This slot is where you connect the HDMI output port of your source equipment such as DVD/Blu-ray players or Set-Top-Box                      with an HDMI cable.
EDID: The switcher can switch copy EDID function, switch to right position, the extender will copy hdmi loop out display EDID
              information to source. Switch to left position, the extender will copy Receiver display EDID to source

HDMI out: This slot is to connect the HDMI input of your display such as an HDTV

IR out: Connect the IR Blaster cable included in the package for IR signal transmission. Pace the IR blaster in direct line-of-sight
                 of the equipment to be controlled

Power LED: This LED will illuminate when the device is connected with power supply

CAT: Connect the CAT output of the transmitter with the CAT input of the receiver with CAT5E/6 cable

Link LED: This LED will illuminate when the device is connected to HDMI source

DC5V: Connect from 5V DC power supply into the unit and connect the adaptor to an AC outlet.

2.       Receiver unit

EQ switcher: HDMI Receiver equalizer switcher

HDMI out: This slot is to connect the HDMI input port of your Display such as an HDTV

IR in: Connect to the IR Receiver for IR signal reception. Ensure that remote being used is within the direct line-of-sight
              of the IR receiver.
Power LED: This LED will illuminate when the device is connected with power supply

CAT: Connect the CAT input of the receiver with the CAT output of the Transmitter with CAT5E/6 cable

Lock LED: This LED will illuminate when the HDMI signal from the Transmitter is stable.

3.RX Equalizer distance adjust
   If you see ?lickering or blinking image on th display, adjust the EQ switch to improve the cable skew. MAX stands for th strongest HDMI signal level for the longest possible transmission length while MIN stands for the weakest HDMI signal level for short transmission length. Adjust the signal level from MIN to MAX until desired video quality is displayed.

Connect and Operate
1.Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit.

2.Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit.

3. Connect a single Category 5e/6 up to 164ft/50m to the output of the transmitting unit, and the other end to the input of the Receiving unit.

4. For power, plug both the Transmitting unit and Receiving unit with the included power supplies.

5. Power on each device in the same sequence (receiver and transmitter will already be powered when either unit is plugged in.)
    At this point the display connected should display the source signal connected to the extender set. If no signal is being displayed, check the receiver EQ switcher. If a display is having difficulty receiving a signal, see EDID section and perform EDID learning or access the display's menu and adjust the resolution(lowest to highest until signal is displayed). A 24 Hz vertical refresh rate may work better than 60 Hz o higher. Use the source remote at the receiver emitter to test IR functionality. If the IR remote function is not responding, check the emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the Extender set receiving and transmitting units.

Wideband IR(30KHz---60KHz) introduction

       IR RECEIVER                                    IR BLASTER
To control the source: Plug IR Blaster into IR TX port transmitter unit; place blaster in front of the IR eye of the source
To control the source: Plug IR Receiver into IR RX port of receiver unit; place receiver at or near display.


Please leave your enquiry here, we will reply as soon as possible.

*only support gif, jpeg, jpg, png, pdf
Switch To Desktop Version